A type of abrasive device that sands or polishes material by rotation.
A type of abrasive shaped like a star used for sanding pipes or similar objects. It works by being rotated by a tool or machine.
A screw with a sharp point and wood screw threads and a hole on the flat end. It can be drivern with a driver tool, or installed using an adjustable wrench or pliers. They are ideal for tie-down and tie-wire applications. Commonly found in suspended ce
An acoustic enclosure (also known as a soundproof enclosure, sound enclosure or noise enclosure) encloses noisy equipment in a room or a chamber.
Acrylic based adhesive that cures in the absence of oxygen
An acrylic based material used to coat electronic component circuitry for protection against environmental or physical damage
Collection of components within a single package and with a single catalog number used to assemble a modular switch.
A part of an adaptor for rolling bearing that has the external diameter surface of taper and the smaller side to insert the nut. It is used to load onto the cylindrical-shaped shaft with the inner diameter of the taper.
An adhesive that is applied as an air spray on the workpieces.
A device that operates aircraft mechanical components such as flaps, slaps, landing gear and others.
Alkyd resin paint is a complex oil-modified polyester that serves as the film-forming agent in some paints and clear coatings, epoxy ester and primers/finishes etc.
Type of screw whose head has a hexagonal socket.
A rope made of aloe vera, a material that makes this rope very resistant to deterioration.
A type of wire made with the main material of aluminum or aluminum alloy.
Aluminum object cast from centrifugal molds
Aluminum object cast from ceramic molds
An adhesive-coated fastening tape made of aluminum used for temporary or, in some cases, permanent adhesion between objects. Commonly used in air-conditioning duct work.
Aluminum object cast from graphite molds
Gravity permanent mold casting made of aluminum
Gravity permanent mold casting made of aluminum that has been machined
An assembly of gravity permanent mold castings made of aluminum that has been machined
Aluminum objects that have been machined to tolerances less than 0.020 mm for major dimensions
High pressure die casting made of aluminum
Aluminum high pressure die casting that has been machined
Aluminum high pressure die casting assembly that has been machined
Aluminum filter sintered at temperatures above 1150 degrees F or 620 degrees centigrade
Aluminum object cast from investment molds
Low pressure permanet mold casting made of aluminum
Low pressure permanet mold casting made of aluminum that has been machined
An assembly of low pressure permanet mold castings made of aluminum that has been machined
Aluminum objects that have been machined to tolerances equal to or greater than 0.020 mm for major dimensions
A type of paint that has the main ingredients of petroleum type synthetic resin and aluminum pigment. The product has strong adhesion, durability and anti-corrosion, outstanding weatherability and moisture resistance, and it is the paint appropriate to the steel-material facilities for the purpose of reflection of hot wire, prevention of moisture penetration and others.
Aluminum object cast from permanent molds
Aluminum object cast from plaster molds
Component stamped from SAE series 1000 aluminum
Component stamped from SAE series 3000 aluminum
Component stamped from SAE series 5000 aluminum
Component stamped from SAE series 6000 aluminum
Aluminum object cast from sand molds
Aluminum object cast from sand molds that has been machined
Assembly of aluminum objects cast from sand molds
Semi solid casting made of aluminum
Semi solid casting made of aluminum that has been machined
An assembly of semi solid castings made of aluminum that has been machined
Aluminum object cast from shell molds
Squeeze casting made of aluminum
Squeeze casting made of aluminum that has been machined
An assembly of squeeze castings made of aluminum that has been machined
Aluminum objects that have been machined to tolerances equal to or greater than 0.050 mm for major dimensions
Aluminum filter sintered at temperatures up to 1150 degrees F or 620 degrees centigrade
Aluminum object cast from v process molds
A type of adhesive that cures in the absence of air.
Gasket formed by the introduction of anaerobic materials that cure in the absence or reduced presence of oxygen, in liquid or semi liquid form between the mating surfaces
A type of washer with a large plate connected to a tie rod or bolt.
Ball bearing that will accept radial loads as well as axial loads in one direction.
An electrically charged device used in corrosion control systems to prevent corrosion of underground or underwater steel structures.
A paint for final application on the surface exposed to the body of a ship and sea water.
Fastening device that prevents loosening of bolts and nuts due to vibration and external force
A type of paint that is made with the raw materials of rust resisting pigment and synthetic resin. This is used with the primer for rust-proofing and repairing of construction iron materials and steel structures.
A line thinner and shorter than a rope comprised of twisted fibers or threads made of asbestos. Insulating properties make it suitable for use with electrical applications.
Rope made of yarn and long fibers of asbestos and roll brading.
Type of actuator used in the operation of automotive vehicular heating, ventilation and air conditioning/circulation systems.
Cover composed of rubber, leather or other pliable material to shield the mechanism of the transmission shift lever.
A paint that is made to form the paint coat by heating after applying the painting. This paint is mainly used for industrial use as home appliance and others.
Studs with a spherical or semi-spherical configuration at the end opposite the threads to facilitate pivoting and/or rotation.
Tapered adapter sleeves used to mount tapered bore bearings.
A principal component in a bearing that enables the reduction of friction.
A device that protects a bearing from contamination and loss of lubricant.There are two types:1/ non-removeable shields or 2/removeable seals that allow the bearing to be cleaned and re-lubricated.
An important individual component of a bearing that is sold separately and serves to decrease the friction of the bearing.
An important individual component of the bearing that is sold separately, and is used to reduce friction inside the bearings.
A sleeve that is used to tighten the bearings with the inner diameter of the taper on the cylindrical shaft.
A type of non-flat washer with aslight conical shape which gives the washer a spring characteristic.
A type of flexible coupling designed to transmit torque while permitting some radial and axial and angular misalignment.
A non pusher design that does not move along the shaft or sleeve to maintain seal face contact. The bellows itself provides the necessary spring loading for seal face contact.
A type of clamp designed to fit workbenches with holes 18-38mm.
Beryllium object cast from centrifugal molds
Beryllium object cast from ceramic molds
Component stamped from beryllium copper
Beryllium object cast from graphite molds
Beryllium filter sintered at temperatures above 1150 degrees F or 620 degrees centigrade
Beryllium object cast from permanent molds
Beryllium object cast from plaster molds
Beryllium object cast from sand molds
Beryllium object cast from shell molds
Beryllium filter sintered at temperatures up to 1150 degrees F or 620 degrees centigrade
Beryllium object cast from v process molds
Flat gasket comprised of various material pairs specifically suited to certain operationg conditions, produced by cutting using punches and dies to achieve desired perimeter shapes
A semi finished product that is designed to meet the special dimensions of user. If needed, the length may be extended with the outline forming, boring, threading and welding, and others.
A multi-leaf chain mainly used in hoist applications.
A special kind of corrosion-resistant fastener designed for marine use in boat and ship building and repair.
A mechanism consisting of a threaded bolt with various head configurations and including other components such as sleeves, expansion devices, etc.
Gasket produced by forming and cutting various metals to achieve desired profile and perimeter shapes, which are then secured to or between sealing surfaces by bolts and nuts
A combined component used to tighten down on the bolt shaft.
A type of washer that acts like a simple pressure gasket providing leak-proof sealing from water, gases, oils and other fluids.
It refers to general hardware for supporting or fixing equipment, equipment, etc. outside a fixed facility such as a building wall or ceiling. However, brackets of parts belonging to the parts of the machine and the device are excluded.
Brass object cast from centrifugal molds
Brass object cast from ceramic molds
Brass object cast from graphite molds
Brass objects that have been machined to tolerances less than 0.020 mm for major dimensions
Brass objects that have been machined to tolerances equal to or greater than 0.020 mm for major dimensions
Brass object cast from permanent molds
Brass object cast from plaster molds
Brass object cast from sand molds
Brass object cast from shell molds
Brass objects that have been machined to tolerances equal to or greater than 0.050 mm for major dimensions
Brass object cast from v process molds
Bronze object cast from centrifugal molds
Bronze object cast from ceramic molds
Bronze object cast from graphite molds
Bronze object cast from permanent molds
Bronze object cast from plaster molds
Bronze object cast from sand molds
Bronze object cast from shell molds
Bronze object cast from v process molds
A solid metallic item, usually cylindrical, with or without a flange at one end which is designed to be inserted into a hole to reduce the inside diameter of the hole and protect the surrounding body structure from damage resulting from stress, strain and/or vibration.
A tubular shaped unthreaded item with or without a flange at one end designed to be inserted into a hole to reduce the inside diameter of the hole and to protect the surrounding body structure from damage resulting from stress, strain, and/or vibration.The overall length must exceed 25 percent of the outside diameter or the shortest distance between peripheral flats of the body.
Used in underground mining applications to support roof.
Used as a positioning connector (hanger) on a wire rope, it allows the wire rope to be inserted into a cam from only one direction without allowing the rope to slip or pull out. It consists of a metal frame with an eye (loop) at one end and a metal cam inside the frame. Once it is slid on the span of the wire rope, it is connected from the eye end to an anchor.
Tape used to repair cable used in undergroud mining. Must be approved for use in application.
A special kind of fastener that is used for square hole racks. It can be of several types: cylindrical, normal, to level out, clip or frontal assembly.
A type seal that is internally sealed, with the fill fluid within the capsule in the upper housing
Component stamped from cold rolled SAE series 1000 carbon steel to which zinc coating has been applied via an immersion process
Component stamped from cold rolled SAE series 1000 carbon steel
Component stamped from tin coated cold rolled SAE series 1000 carbon steel
Component stamped from cold rolled SAE series 1000 carbon steel to which zinc coating has been applied via an electroplating process
Component stamped from hot rolled SAE series 1000 carbon steel
A mushroom-shaped head screw with a square neck, made of steel or stainless steel, this screw is under the DIN standard number 603, it usually includes a hex nut.
Bearing having the same properties as radial ball bearings except a wider width.
Anisotropic barium ferrite magnet assembly that has been cast
Anisotropic ferrite magnet assembly that has been cast
Anisotropic ferrous aluminum nickel cobalt magnet assembly that has been cast
Anisotropic samarium magnet assembly that has been cast
Anisotropic strontium ferrite magnet assembly that has been cast
Cast anisotropic barium ferrite magnet that has been coated
Cast anisotropic ferrite magnet that has been coated
Cast anisotropic ferrous aluminum nickel cobalt magnet that has been coated
Cast anisotropic samarium magnet that has been coated
Cast anisotropic strontium ferrite magnet that has been coated
Cast isotropic barium ferrite magnet that has been coated
Cast isotropic ferrite magnet that has been coated
Cast isotropic ferrous aluminum nickel cobalt magnet that has been coated
Cast isotropic neodymium magnet that has been coated
Cast isotropic samarium magnet that has been coated
Cast isotropic strontium ferrite magnet that has been coated
Cast steel nodes are being increasingly popular in steel structure joint application as their advanced mechanical performances and flexible forms. This kind of joints improves the structural antifatigue capability observably and is expected to be widely used in the structures with fatigue loadings.
Isotropic barium ferrite magnet assembly that has been cast
Isotropic ferrite magnet assembly that has been cast
Isotropic ferrous aluminum nickel cobalt magnet assembly that has been cast
Isotropic neodymium magnet assembly that has been cast
Isotropic samarium magnet assembly that has been cast
Isotropic strontium ferrite magnet assembly that has been cast
Cast anisotropic barium ferrite magnet that has been machined and coated
Cast anisotropic ferrite magnet that has been machined and coated
Cast anisotropic ferrous aluminum nickel cobalt magnet that has been machined and coated
Cast anisotropic samarium magnet that has been machined and coated
Cast anisotropic strontium ferrite magnet that has been machined and coated
Cast isotropic barium ferrite magnet that has been machined and coated
Cast isotropic ferrite magnet that has been machined and coated
Cast isotropic ferrous aluminum nickel cobalt magnet that has been machined and coated
Cast isotropic neodymium magnet that has been machined and coated
Cast isotropic samarium magnet that has been machined and coated
Cast isotropic strontium ferrite magnet that has been machined and coated
Cast anisotropic barium ferrite magnet that has been machined
Cast anisotropic ferrite magnet that has been machined
Cast anisotropic ferrous aluminum nickel cobalt magnet that has been machined
Cast anisotropic samarium magnet that has been machined
Cast anisotropic strontium ferrite magnet that has been machined
Cast isotropic barium ferrite magnet that has been machined
Cast isotropic ferrite magnet that has been machined
Cast isotropic ferrous aluminum nickel cobalt magnet that has been machined
Cast isotropic neodymium magnet that has been machined
Cast isotropic samarium magnet that has been machined
Cast isotropic strontium ferrite magnet that has been machined
Cast anisotropic barium ferrite magnet that has been cast off-tool
Cast anisotropic ferrite magnet that has been cast off-tool
Cast anisotropic ferrous aluminum nickel cobalt magnet that has been cast off-tool
Cast anisotropic samarium magnet that has been cast off-tool
Cast anisotropic strontium ferrite magnet that has been cast off-tool
Cast isotropic barium ferrite magnet that has been cast off-tool
Cast isotropic ferrite magnet that has been cast off-tool
Cast isotropic ferrous aluminum nickel cobalt magnet that has been cast off-tool
Cast isotropic neodymium magnet that has been cast off-tool
Cast isotropic samarium magnet that has been cast off-tool
Cast isotropic strontium ferrite magnet that has been cast off-tool
A device designed to tighten by activating a spring motion ball, bolt, plunger, double bevel latch and others. The device is inserted and maintained by the spring compression on the concave surface, strike, or latch.
Powdered metal comprising any generally accepted cemented carbide compositions of carbide particles and metallic binders
A line thinner and shorter than a rope made of ceramic fiber, a material very resistant to high temperatures.
Ceramic objects that have been machined to tolerances less than 0.020 mm for major dimensions
Ceramic filter sintered at temperatures above 1150 degrees F or 620 degrees centigrade
Ceramic objects that have been machined to tolerances equal to or greater than 0.020 mm for major dimensions
Ceramic objects that have been machined to tolerances equal to or greater than 0.050 mm for major dimensions
Ceramic filter sintered at temperatures up to 1150 degrees F or 620 degrees centigrade
Coupling that uses double roller chain to connect two hubs.
A chain pulley, or sprocket wheel.
A type of spring ring, but smaller, that has a hole at either end for receiving the pins of special pliers.
A type of coupling sometimes called a compression coupling or a ribbed coupling. It is a modification and an improvement on the sleeve coupling.
A type seal clamped between the upper and lower housing allowing it to be removed and replaced easily
A type of washer used when there is not enough room for a standard washer and also the washer will not rotate.
A type of steel wire coated or plated with other metals, such as zinc or aluminum.
A rope made of coconut fiber that has high lignin content and low cellulose content, making it resilient and durable, this ropes are rough and strong.
Forging made of aluminum that is forged at a cold temperature and has been heat treated
Forging made of aluminum that is forged at a cold temperature and has been heat treated and cold sized
Forging made of beryllium that is forged at a cold temperature and has been heat treated and cold sized
Forging made of brass that is forged at a cold temperature and has been heat treated and cold sized
Forging made of bronze that is forged at a cold temperature and has been heat treated and cold sized
Forging made of copper that is forged at a cold temperature and has been heat treated and cold sized
Forging made of ferrous alloy that is forged at a cold temperature and has been heat treated and cold sized
Forging made of iron that is forged at a cold temperature and has been heat treated and cold sized
Forging made of lead that is forged at a cold temperature and has been heat treated and cold sized
Forging made of magnesium that is forged at a cold temperature and has been heat treated and cold sized
Forging made of non ferrous alloy that is forged at a cold temperature and has been heat treated and cold sized
Forging made of precious metal that is forged at a cold temperature and has been heat treated and cold sized
Forging made of stainless steel that is forged at a cold temperature and has been heat treated and cold sized
Forging made of steel that is forged at a cold temperature and has been heat treated and cold sized
Forging made of tin that is forged at a cold temperature and has been heat treated and cold sized
Forging made of titanium that is forged at a cold temperature and has been heat treated and cold sized
Forging made of zinc that is forged at a cold temperature and has been heat treated and cold sized
Forging made of beryllium that is forged at a cold temperature and has been heat treated
Forging made of brass that is forged at a cold temperature and has been heat treated
Forging made of bronze that is forged at a cold temperature and has been heat treated
Forging made of copper that is forged at a cold temperature and has been heat treated
Forging made of ferrous alloy that is forged at a cold temperature and has been heat treated
Forging made of iron that is forged at a cold temperature and has been heat treated
Forging made of lead that is forged at a cold temperature and has been heat treated
Forging made of magnesium that is forged at a cold temperature and has been heat treated
Forging made of non ferrous alloy that is forged at a cold temperature and has been heat treated
Forging made of precious metal that is forged at a cold temperature and has been heat treated
Forging made of stainless steel that is forged at a cold temperature and has been heat treated
Forging made of steel that is forged at a cold temperature and has been heat treated
Forging made of tin that is forged at a cold temperature and has been heat treated
Forging made of titanium that is forged at a cold temperature and has been heat treated
Forging made of zinc that is forged at a cold temperature and has been heat treated
Forging made of aluminum that is forged at a cold temperature and has been machined
Forging made of aluminum that is forged at a cold temperature and has been machined and heat treated
Forging made of beryllium that is forged at a cold temperature and has been machined and heat treated
Forging made of brass that is forged at a cold temperature and has been machined and heat treated
Forging made of bronze that is forged at a cold temperature and has been machined and heat treated
Forging made of copper that is forged at a cold temperature and has been machined and heat treated
Forging made of ferrous alloy that is forged at a cold temperature and has been machined and heat treated
Forging made of iron that is forged at a cold temperature and has been machined and heat treated
Forging made of lead that is forged at a cold temperature and has been machined and heat treated
Forging made of magnesium that is forged at a cold temperature and has been machined and heat treated
Forging made of non ferrous alloy that is forged at a cold temperature and has been machined and heat treated
Forging made of precious metal that is forged at a cold temperature and has been machined and heat treated
Forging made of stainless steel that is forged at a cold temperature and has been machined and heat treated
Forging made of steel that is forged at a cold temperature and has been machined and heat treated
Forging made of tin that is forged at a cold temperature and has been machined and heat treated
Forging made of titanium that is forged at a cold temperature and has been machined and heat treated
Forging made of zinc that is forged at a cold temperature and has been machined and heat treated
Forging made of beryllium that is forged at a cold temperature and has been machined
Forging made of brass that is forged at a cold temperature and has been machined
Forging made of bronze that is forged at a cold temperature and has been machined
Forging made of copper that is forged at a cold temperature and has been machined
Forging made of ferrous alloy that is forged at a cold temperature and has been machined
Forging made of iron that is forged at a cold temperature and has been machined
Forging made of lead that is forged at a cold temperature and has been machined
Forging made of magnesium that is forged at a cold temperature and has been machined
Forging made of non ferrous alloy that is forged at a cold temperature and has been machined
Forging made of precious metal that is forged at a cold temperature and has been machined
Forging made of stainless steel that is forged at a cold temperature and has been machined
Forging made of steel that is forged at a cold temperature and has been machined
Forging made of tin that is forged at a cold temperature and has been machined
Forging made of titanium that is forged at a cold temperature and has been machined
Forging made of zinc that is forged at a cold temperature and has been machined
A compound applied to bare clean steel for excellent corrosion protection. This coating was originally developed to prevent bare steel structures from rusting when exposed to the elements.
Flange or other bushing formed by cold heading.
A filter that absorbs the opposite color that the filter has among three primary colors of light and emphasizes the color of the subject similar to the filter color and makes the other different colored subject darker.
Bearing having both ball and roller bearings, one to take thrust load while the other accepts radial load.
A bearing that is designed for integrated use of needle roller and ball with the space saving-type by having the needle roller receive the load in the radial direction and having the ball receive the load in the shaft direction. This bearing is used for transmission engineering, machine tool and others.
A stud like component with other than straight shaft or other complex physical characteristics
Flat gasket comprised of fibrous materials that have been compressed into sheet form, produced by cutting using punches and dies to achieve desired perimeter shapes
A type of fastener designed for use with composite materials such as concrete.
A type of adhesive that works only through the contact of two surfaces. It is fast drying, flammable and can be composed of different materials such as latex or rubber.
An elongated control device generally shaped like an arm. There are remote control levers and manual control levers.
Chain designed to be used as a conveyor, generally with table top attachments.
A type of sprocket for use with conveyor or table top chain.
Copper based filter sintered at temperatures up to 1150 degrees F or 620 degrees centigrade
Copper object cast from centrifugal molds
Copper object cast from ceramic molds
Copper object cast from graphite molds
A type of wire made with the main material of copper or copper alloy.
Copper object cast from permanent molds
Copper object cast from plaster molds
Copper object cast from sand molds
Copper object cast from shell molds
Copper object cast from v process molds
Flat gaskets produced by cutting cork sheet materials using punches and dies to achieve desired perimeter shapes
Gasket produced by forming and cutting cork to achieve desired profile and perimeter shapes
Cork gasket produced by cutting using ultra high pressure water jets
A length of flexible material similar to rope, but thinner and shorter, made of cotton fibers braided together.
A type of washer that provides the same function as a flat washer except when used with flat head screws.In this case, it provides a sealing function for flat head screws used in a countersunk hole.
A type of coupling for interconnecting fire or other hose to a reciprocal connection mounted on another hose or on a fixed object.
A device that connects the drive wheels of a locomotive.
A type of washer designed to protect the head of a metal screw from electrical contact.
Aggressive fast acting liquid adhesive based on various cyanoacrylate compounds
A type of bearing that has high radial capacity.These bearings feature low friction, which permits operation at high speed.
A disk or wheel, having cut teeth of such form, size, and spacing that they mesh with teeth in another part to transmit or receive force and motion.
A fastening device employing a shaft to connect two materials while enabling their movement.
A type of fastener that has a decorative as well as attachment function.
A fastener whose form or color is decorative as well as functional.
A special kind of screw that has an extra function, decorate, it is available in several forms and colors.
Powdered composite comprising diamond powder and a powdered metal or metals
A dichroic filter or thin-film filter is a very accurate color filter used to selectively pass light of a small range of colors while reflecting other colors
Flat gasket kit produced by cutting various sheet materials using punches and dies to achieve desired perimeter shapes
Seal kit for seals produced by cutting various sheet materials using punches and dies to achieve desired perimeter shapes
Coupling that uses one or more disks or disk packs to connect two hubs via staggered pins.
A stud threaded at both ends.
Chain built to exact specifications used for lifting or dragging dragline buckets.
A type of holding device designed to keep drilling tools in place and immobile. It can include claws for better support.
A type of rivet that has a short mandrel protruding from the head that is driven in with a hammer to flare out the end inserted in the hole.
Ductile iron object cast from sand molds
Ductile iron object cast from sand molds that has been machined
Assembly of ductile iron objects cast from sand molds
Ductile iron object cast from shell molds
Ductile iron object cast from shell molds that has been machined
Assembly of ductile iron object cast from shell molds that has been machined
A coupling that is formed with two elements of urethane rubber and metal hub that may permit the eccentricity between axes. It has outstanding oil-free and chemical resistance properties.
Various sinterable metal powders exhibiting a high degree of electical conductivity and wear resistance used in applications involving electrical circuits
An adaptor that is used to electrically or physically connect for equipment to equipment, or equipment and other subject.
Gasket comprised of various materials designed to prevent or reduce EMI, produced by various molding processes
Flat gasket produced by cutting sheets comprised of various materials designed to prevent or reduce EMI, using punches and dies to achieve desired perimeter shapes
Gasket comprised of various materials designed to prevent or reduce EMI, produced by cutting using ultra-high pressure water jets
A metric screw (DIN 15237) with a large head diameter, zinc plated as standard or stainless, and with bolt hex nut small.
A type of hinge designed and built for specific purposes beyond typical standard applications.
Chain designed to operate in elevators, drives and rugged conveyor service.
A type of sprocket for use with engineered chains.
Epicyclic Gearbox is also known as Planetary Gearbox or Planetary Gear Train or Epicyclic Gear Train. It is used as a transmission system to get various speed ratios in forward as well as in reverse directions.
An epoxy based material used to coat electronic component circuitry for protection against environmental or physical damage
It is an airtight sealer that protects the primer before the walls are ready for paint. It also acts as a binding ingredient between the concrete, and the topcoat of the paint. Epoxy primer paint protects the walls from extreme weather conditions. It is a two component, Epoxy Zinc Phosphate high performance primer for new and maintenance application. Advanced 2-pack epoxy primer Grey is equipped with surface tolerant property that is designed to offer excellent corrosion protection to mild steel substrates.
A chain used exclusively for escalators that causes the step to move which is the part passengers step onto.
A tough, wiry grass (Stipa tenacissima) of northern Africa and south Spain, yielding a fiber used in making ropes very resistants and with a long life.
A device used to join, support or compress mechanical or structural parts. One or both arms of the clamp are adjustable to accommodate the size of the workpiece.
A screw that is characterized by the hole in the head, it accomplishes the DIN 444 standard.
An assortment of fasteners packaged as a kit.
A type of washer that is much larger in diameter than the bolt with which it is used. This gives the washer the ability to distribute the bolt force over a wider area.
Ferrous alloy object cast from centrifugal molds
Ferrous alloy object cast from ceramic molds
Ferrous alloy object cast from graphite molds
Ferrous alloy object cast from investment molds
Ferrous alloy object cast from permanent molds
Ferrous alloy object cast from plaster molds
Ferrous alloy object cast from sand molds
Ferrous alloy object cast from shell molds
Ferrous alloy object cast from v process molds
A specialized fastener used to connect corrugated sheets (undulated plates of fiber cement). It is a thin nail with an elongated head.
An elastomeric or other polymeric diaphragm seal reinforced with glass, carbon or other fibers
A hook in the shape of the figure 8, closed in on one side and slightly open on the other.
A type of washer designed to reduce noise and vibration and to prevent excess wear especially at high speeds.
A type of stain that has a nitrocellulose lacquer added to it used to finish a product
A brick that is one of the fire bricks most widely used in various furnaces as the fire bricks that have the main ingredients of fire clay, agalmatolite, and others.
A powdery castable refractory with the main raw materials in fire clay, agalmatolite or others. The strength is displayed by the hydration reaction with the addition of appropriate volume of moisture.
A hook similar to a square hook but it is not portable. It is affixed to the wall.
A type of coupling having two separate cast iron flanges.Each flange is mounted on the shaft end and keyed to it.
A coupling that drills the diameter of the bolt hole of the main body of the flange slightly large to permit the deviation of the shaft center in a way of inserting the bush and convey the power by fixing the flange with the bolt.
A plane mirror for optical equipment that is used to engage in image or change the direction by reflecting the light.
A type of bearing which allows motion by bending a load element.
A ring which is either machined around a shaft or fixed on it.
Adhesive substance containing a significant percentage of a fluorocarbon elastomer
A type of rivet used primarily on external metal surfaces where good appearance and the elimination of unnecessary aerodynamic drag are important.
Mini-molded handles with foam mitt used to apply chalk, ink, paint or adhesive
Seal produced by cutting various open or closed cell foam sheet materials using punches and dies to achieve desired perimeter shapes
Used to seal, waterproof, and protect various items in a variety of situations
A product that foams and hardens when injected into empty hole in pipeline and gaps as a foaming resin.
Single row bearing designed to take radial load as well as axial load in both directions.
A coupling that is tightened by pounding at both ends of the soft steel ring. After covering the connection part of both axes has the cast iron split muff with the surrounding conical shape.
Various sinterable metal powders combined with friction enhancing materials used to produce a product with high coefficients of friction
An iron net that is made for the net shape to fill in the stones. This product is widely used in various revetment works or watercourse works by filling the rocks.
A representative optical absorption filter that is from the colored filters that penetrates the specific wavelength and absorbs the other wavelengths. It is made by forming the thin film on the glass substrate with the organic pigment dissolved in the gelatin solution.
A fastener or fastening is a hardware device that mechanically joins or affixes two or more objects together. In general, fasteners are used to create non-permanent joints; that is, joints that can be removed or dismantled without damaging the joining components.
In piping, a Gasket is sealing material placed between connecting flanges to create a static seal. This will maintain the leakage-proof sealing in all operating conditions. Different types of gaskets are used to achieve leakproof sealing between the pipe flanges.
Insulation gasket act as an insulator between dissimilar metallic flanges. Also, they are used to isolate sections of pipework (dissimilar metals) electrically in the cathodic protection systems, thus preventing the electrostatic charge flow along the pipelines as they remove the possibility of galvanic cell system creation.
A jointing gasket is a type of gasket that is used to provide a tight seal between two mating surfaces that have irregular or non-parallel surfaces. They are typically made from materials such as rubber, cork, or fiber and can be cut or molded to fit the shape of the mating surfaces. Jointing gaskets are designed to compress and fill the gaps between the mating surfaces, which creates a seal that prevents the leakage of fluids or gases. They can be used in various applications where a tight seal is required, including in pipe fittings, flanges, and valve bonnets.The assembly of components (eg-flanges, bolts, gaskets etc.) required to join two or more items of process equipment and to prevent leakage.
A substance used to prime surface of canvas for acrylic paint. Used in sculpture or as a base for gilding or painting on wood.
A type of power transmission device similar to the square key.
A line thinner and shorter than a rope that is made of fiber cord, a very resistant material.
Specific chain equipped with metal and/or rubber paddles fitted into grain tank elevator or grain return elevator used for carrying cereals to a grain tank or to separation system.
Grey iron object cast from sand molds
Grey iron object cast from sand molds that has been machined
Assembly of grey iron objects cast from sand molds
Coupling that uses a serpentine grid to connect two hubs.
A coupling that has the structure to deliver power by inserting the grid to the grooves that are paved on the hub.
An anchor used to secure a civil work or construction structure into the ground foundation or base rock. The steel wire and the grout are used in general.
A type of set screw having no projecting head.Its top is either slotted or provided with a socket.
A bearing that determines the shaft location or undertakes the role to guide the simple linear motion, not a bearing that supports the load applied to the rotating shaft.
A coupling that secures the common key by overlapping at both ends to make slightly larger and sloped within the muff.
A metal fastener largerr than the standard nut with a central, threaded hole that is designed to fit around and secure a bolt or a screw as well as part of the surface where it is placed.
A fastener with a T-shaped square neck.
A type of clamp also known as 'toolmaker's clamp' that is used mainly in metalwork.The adjustable jaws will fit angled material.
A headless bolt that is designed to connect a round bar and hanger to tie up to the ceiling.
A wire made from metal drawn at room temperature after the thermal disposition of the hard drawn steel material is made from high carbon wire rod.
A paint that is used for the long-term conservation of steel structures, such as bridge, marine structure, power plant, various plants, ships and others which has special environment of the plant area and the coastal area that inflict severe corrosion to the steel structure, unlike general structures.
Type of gear with two opposing helices to transmit power and motion between parallel axes.The mirrored halves of the gear face have teeth that resemble an arrow head or the letter V.
A screw with hexagonal head that follows DIN standard numbers like 931, 933 or 961.
A powdery castable refractory that is manufactured and kneaded by using alumina silica as the main binding agent (50% or more). The strength is displayed by the hydration reaction with the added appropriate volume of moisture.
A bearing for unit that prevents heat, vibration, noise and others which may be generated by high-speed rotation or is designed to display its capability required under the adverse environment of dust-proof, water-proof, heat-resistance, cold-resistance and others.
A horizontal gearbox is designed in such a way that it decreases the speed by increasing the torque significantly. Horizontal worm gearboxes are ideal for heavy load works and power transmission.
Type of paint specially formulated for resisting high temperatures, such as: heaters, furnaces, chimneys, reactors, heat ducts, etc.
A serial chain used in industrial machines to be inserted in the sprockets, the hollow pin is at the center of articulation, and always keeps the pitch length.
A bolt that has a hook shaped head.
A special kind of fastener designed to attach an iron or steel shoe to the hoof of a horse.
Forging made of beryllium that is forged at a hot temperature and has been heat treated and cold sized
Forging made of bronze that is forged at a hot temperature and has been heat treated and cold sized
Forging made of copper that is forged at a hot temperature and has been heat treated and cold sized
Forging made of ferrous alloy that is forged at a hot temperature and has been heat treated and cold sized
Forging made of iron that is forged at a hot temperature and has been heat treated and cold sized
Forging made of lead that is forged at a hot temperature and has been heat treated and cold sized
Forging made of magnesium that is forged at a hot temperature and has been heat treated and cold sized
Forging made of non ferrous alloy that is forged at a hot temperature and has been heat treated and cold sized
Forging made of precious metal that is forged at a hot temperature and has been heat treated and cold sized
Forging made of stainless steel that is forged at a hot temperature and has been heat treated and cold sized
Forging made of steel that is forged at a hot temperature and has been heat treated and cold sized
Forging made of tin that is forged at a hot temperature and has been heat treated and cold sized
Forging made of titanium that is forged at a hot temperature and has been heat treated and cold sized
Forging made of zinc that is forged at a hot temperature and has been heat treated and cold sized
Forging made of beryllium that is forged at a hot temperature and has been heat treated
Forging made of bronze that is forged at a hot temperature and has been heat treated
Forging made of copper that is forged at a hot temperature and has been heat treated
Forging made of ferrous alloy that is forged at a hot temperature and has been heat treated
Forging made of iron that is forged at a hot temperature and has been heat treated
Forging made of lead that is forged at a hot temperature and has been heat treated
Forging made of magnesium that is forged at a hot temperature and has been heat treated
Forging made of non ferrous alloy that is forged at a hot temperature and has been heat treated
Forging made of precious metal that is forged at a hot temperature and has been heat treated
Forging made of stainless steel that is forged at a hot temperature and has been heat treated
Forging made of steel that is forged at a hot temperature and has been heat treated
Forging made of tin that is forged at a hot temperature and has been heat treated
Forging made of titanium that is forged at a hot temperature and has been heat treated
Forging made of zinc that is forged at a hot temperature and has been heat treated
Forging made of beryllium that is forged at a hot temperature and has been machined and heat treated
Forging made of bronze that is forged at a hot temperature and has been machined and heat treated
Forging made of copper that is forged at a hot temperature and has been machined and heat treated
Forging made of ferrous alloy that is forged at a hot temperature and has been machined and heat treated
Forging made of iron that is forged at a hot temperature and has been machined and heat treated
Forging made of lead that is forged at a hot temperature and has been machined and heat treated
Forging made of magnesium that is forged at a hot temperature and has been machined and heat treated
Forging made of non ferrous alloy that is forged at a hot temperature and has been machined and heat treated
Forging made of precious metal that is forged at a hot temperature and has been machined and heat treated
Forging made of stainless steel that is forged at a hot temperature and has been machined and heat treated
Forging made of steel that is forged at a hot temperature and has been machined and heat treated
Forging made of tin that is forged at a hot temperature and has been machined and heat treated
Forging made of titanium that is forged at a hot temperature and has been machined and heat treated
Forging made of zinc that is forged at a hot temperature and has been machined and heat treated
Forging made of beryllium that is forged at a hot temperature and has been machined
Forging made of bronze that is forged at a hot temperature and has been machined
Forging made of copper that is forged at a hot temperature and has been machined
Forging made of ferrous alloy that is forged at a hot temperature and has been machined
Forging made of iron that is forged at a hot temperature and has been machined
Forging made of lead that is forged at a hot temperature and has been machined
Forging made of magnesium that is forged at a hot temperature and has been machined
Forging made of non ferrous alloy that is forged at a hot temperature and has been machined
Forging made of precious metal that is forged at a hot temperature and has been machined
Forging made of stainless steel that is forged at a hot temperature and has been machined
Forging made of steel that is forged at a hot temperature and has been machined
Forging made of tin that is forged at a hot temperature and has been machined
Forging made of titanium that is forged at a hot temperature and has been machined
Forging made of zinc that is forged at a hot temperature and has been machined
A sound attenuator, or duct silencer, sound trap, or muffler, is a noise control acoustical treatment of Heating Ventilating and Air-Conditioning (HVAC) ductwork designed to reduce transmission of noise through the ductwork, either from equipment into occupied spaces in a building, or between occupied spaces.
Cover for mechanism of ignition/key system.
A special kind of rope that is impregnated with another substance to strengthen or improve performance under specific conditions. Examples include resin or tar-impregnated rope.
Type of sealant designed for use with micro porosity in castings, powder metal parts, gemstones, ceramics, plastics and other porous substrates
Component stamped from any of the family of specialist superalloys based on austenitic nickel chromium
Gasket comprised of various materials, produced by various molding processes, whose sealing ability is achieved or enhanced via inflation of an inner chamber of the gasket
Spring used in the control of automotive fuel injection valves.
Injection molded component consisting of various plastic materials with the addition of a decorative formed panel placed into some portion of the show surface side of the injection mold prior to injection of the plastic
Injection molded component consisting of various plastic materials with the addition of a decorative pigment contained on some carrier placed into some portion of the show surface side of the injection mold prior to injection of the plastic
Bearing designed to be mounted into housing.
A bearing for unit that is used for consistent rotation direction. The inner collar is expanded in one or both sides and the standard product has two lubricant injection holes on the outer collar.
A bearing for unit that has the two fixed screws (grubs or set screws) on the inner collar. This device is appropriate to the device with the changing rotation direction. The inner collar is expanded on both sides and the standard product has two lubricant injection holes on the outer collar.
A bearing for unit that is appropriate to the high-speed device with changing rotation direction. The width of inner collar and outer collar is the same and the standard product has two lubricant injection holes on the outer collar.
A type of contact adhesive usually comprised of Cyanoacrlylate --a generic name for substances such as methyl-2-cyanoacrylate- that cures quickly and is used with wood, metals, rubber and plastics.
A filter that filters the wave of specific wavelength by using the interference phenomenon that arises on thin film.
A cylindrical shaped nut that has the inner part processed in spline shape to use the opposite sides of the bearing side as used with the insertion wrench.
Iron object cast from centrifugal molds
Iron object cast from ceramic molds
Iron copper filter sintered at temperatures up to 1150 degrees F or 620 degrees centigrade
Iron object cast from graphite molds
Iron object cast from investment molds
Iron object cast from permanent molds
Iron object cast from plaster molds
Iron object cast from v process molds
Wire made of iron.
A type of clamp designed to be used on hoses and pipes to reduce sound vibrations.
A Jacket structure is a welded tubular space frame consisting of vertical or battered legs supported by a lateral bracing system. The function of the jacket is to support the topside facilities, provide supports for conductors, risers, and other appurtenances, and serve as a template for the foundation system.
A mechanism that uses a long threaded rod to position a matching nut at any position along its length.
A type of coupling device that requires no lubrication and has no metal to metal contact.
Material that is made for jewelry, like, sapphire, ruby and others, non-magnetic substance with a little loss on torque and friction of bearing for freely rotating equipment by securing the rotating shaft or axle and others of a machine on certain location.
A bearing that supports the radial load that works vertically to the rotating shaft by forming the oil film from the sliding rotation for the bearing and journal.
Jute is a long, soft, shiny vegetable fibre that can be spun into coarse, strong threads, it is produced from plants in the genus Corchorus, family Malvaceae, jute rope is very widely used in a lot of fields.
Also called a K-nut or washer nut.It is a nut with an attached, free-spinning washer used to make assembly more convenient
A group of wire strands bundled or twisted together as a laminated functional unit.
Injection molded component consisting of various plastic materials that is treated with laser to produce etching or other decorative effects to its show surface and is painted to highlight or accentuate the decorative effect
Injection molded component consisting of various plastic materials that is treated with laser to produce etching or other decorative effects to its show surface
A length of flexible material similar to rope, but thinner and shorter, made of cotton fibers braided together.
Dip molding produced from various latex compounds
A flexible rope made of latex that makes it exceptionally abrasion resistant and UV radiation resistant.
A kit for seals produced by turning to achieve desired inner and outer diameters and thicknesses
Lead object cast from centrifugal molds
Lead object cast from ceramic molds
A type of foil tape with lead foil as the carrier material and an adhesive as backing. Used as a barrier against humidity and radiation in some situations.
Lead object cast from graphite molds
Lead object cast from investment molds
A type of wire made with the main material of lead or lead alloy.
Lead object cast from permanent molds
Lead object cast from plaster molds
Lead object cast from sand molds
A leadscrew is a screw specialized for the purpose of translating rotational to linear motion.
Lead object cast from shell molds
Lead object cast from v process molds
A cylindrical roller that has the hole in the central location in order to accommodate the pin or shaft to combine the push stick, inducement device, joint, rocker arm, rotation table or horizontal bar.
Linen is a material made from the fibers of the flax plan, the linen rope is used in lots of fields like textile, footwear or others.
All types of line tape.
An annular shaft seal for sealing against oil which is flexible and uses an interference fit on the shaft and deformation stress to maintain the seal.
A ring that is designed to secure the shaft-direction location by loading onto the outside diameter of the rolling bearing.
A detent that is used for rolling bearing. It undertakes the roll to prevent the rotation of nuts for adaptor and shaft and it is used for the inside diameter number 44 or higher.
Chain used in conjunction with flights to move coal from where it is being mined to conveyors. High impact resistant chain for use on heavy duty longwall haulage and conveyors.
A type of wire generally referred to as iron wire. It has a carbon content ranging from of 0.06 percent to 0.25 percent and a tensile strength of 35 kilograms per square millimeter.
A type of optical filter named for its inventor Bernard Lyot, that uses birefringence to produce a narrow passband of transmitted wavelengths.
Magnesium object cast from centrifugal molds
Magnesium object cast from ceramic molds
Magnesium object cast from graphite molds
High pressure die casting made of magnesium
Magnesium high pressure die casting that has been machined
Magnesium high pressure die casting assembly that has been machined
Magnesium object cast from investment molds
Magnesium object cast from permanent molds
Magnesium object cast from plaster molds
Magnesium object cast from sand molds
Magnesium object cast from shell molds
Magnesium object cast from v process molds
A type of coupling designed to transmit rotational and/or linear motion without direct contact using a magnetic field.
Malleable iron object cast from sand molds
Malleable iron object cast from sand molds that has been machined
Assembly of malleable iron objects cast from sand molds
Also called inverted marking paint. Used in surveying, sports, construction and highway engineering to mark ground surfaces.
A device used to join lengths of rebar together.
Seal kit for seals designed to prevent leakage between a rotating shaft and its housing.
Mechanical seals are devices that are used to provide a seal at the point of entry or exit of a rotating shaft. Simply a method of containing fluid within a vessel (typically pumps, mixers, etc.) where a rotating shaft passes through a stationary housing or occasionally, where the housing rotates around the shaft.
A length of flexible material similar to rope, but thinner and shorter, made of metallic fibers braided together.
A type of seal made of metal produced by turning to achieve desired inner and outer diameters and thicknesses
Injection molded component consisting of various plastic materials with the addition decorative metallic finish applied to its show surface after molding, using an electrostatic evaporative coating process
A fastener made of metal used to secure the parts of a chain.
Gasket produced by forming and cutting various ferrous and non ferrous metals to achieve desired profile and perimeter shapes
A type of clamp designed for use with small workpieces or used in small spaces.
A type of clamp designed for gripping two pieces of material with mitered ends at right angles. There are two types: internal (upper) or external (lower).
Gasket kit produced by various molding processes
Injection molded component consisting of various plastic materials with the addition of a pigment to achieve a specified color during molding.
A mono tower substructure is an offshore platform without any workers, which has one leg. Usually comprises a superstructure supported on a single vertical leg.
A type of adhesive used for attaching a graphic image --a photograph, print or poster, for example-- to a board substrate which may be rigid or semi-rigid.
A type of device that has two shafts to face and fit together within a cast iron or cast steel cylinder and is bound with keys. This device is the simplest coupling to use if the axis diameter and the load for conveyance are very small.
Injection molded component consisting of various plastic materials manufactured by introducing multiple melt flows to produce the desired surface effect
A type of multi-purpose glue that can be used to bind many different types of materials together. Constituent materials vary.
A length of flexible material similar to rope, but thinner and shorter, made of neoprene fibers braided together.
Dip molding produced from various neoprene compounds
A type of seal made of neoprene produced by turning to achieve desired inner and outer diameters and thicknesses
A type of wire made with an alloy of nickel and chrome.
Nickel cobalt filter produced by sintering previously compacted powders at temperatures up to 1150 degrees F or 620 degrees centigrade
Nickel cobalt filter sintered at temperatures above 1150 degrees F or 620 degrees centigrade
Nickel cobalt filter sintered at temperatures up to 1150 degrees F or 620 degrees centigrade
A type of wire made with the main material of nickel or nickel alloy.
Noise lagging panels are designed to block noise that transmits through the walls.
Cable with non electrical properties made of iron.
Non ferrous alloy object cast from centrifugal molds
Non ferrous alloy object cast from ceramic molds
Non ferrous alloy object cast from graphite molds
Non ferrous alloy object cast from investment molds
Non ferrous alloy object cast from permanent molds
Non ferrous alloy object cast from plaster molds
Non ferrous alloy object cast from sand molds
Non ferrous alloy object cast from shell molds
Non ferrous alloy object cast from v process molds
A type of washer generally used with a key to prevent rotation of the washer relative to the shaft.
A length of flexible material similar to rope, but thinner and shorter, made of nylon fibers braided together.
A bearing that is consisted of sleeves made in material of oilless metal that is contained of the firm shaft and lubricant oil which is used in the parts with less load applied. This is mainly used in the small motors, such as the cooling fan for computer.
Oil seals, also referred to as shaft seals, are widely used to prevent the leakage of medium (such as oils and grease) along a rotating shaft. This leak prevention is primarily achieved by the sealing element which can be made from a wide range of materials that are chosen according to each application. They are commonly used in gearboxes, hydraulic cylinders, and related components. Oil seals are used to protect shafts and bearings from ingress of dirt and foreign matter and egress of oil or grease. An oil seal generally consists of an outer circular metal part and an inner flexible member that does the actual sealing and is bonded to the metal part by chemical adhesive agents.
A type of wire made by the tempering process after quenching the cold work wire and oil in consecutive passes.
A type of coupling consisting of a pair of disks, one flat and the other hollow, both pinned to the ends of the shafts.A third, center disk with a pair of lugs projecting from each face of the disk fits into the slots between the two end disks and enables one shaft to drive the other shaft.
An experimental board designed to provide convenience in observation of spectrum or experimenting optical phenomenon such as diffraction and interference of light.
O ring gasket produced by various molding processes
O-rings seals are very commonly found in pumps, cylinders, connectors and valves, helping to seal joins between separate parts and prevent leaking of fluids and gases. They're used with static, dynamic, hydraulic and pneumatic components, making them an especially versatile solution to a very widespread engineering issue.
A bolt that has an elliptical neck under the head. This bolt has the head with the nominal diameter.
Injection molded component consisting of various plastic materials with the addition paint applied to its show surface after molding
Used to cover paint rollers that are used for applying paint, stain, etc.
A disposable liner made of plastic material molded to fit inside that paint tray to protect it.
A small slender pin with a very small head, mainly used for attaching plywood or hardboard to supports.
A chemical vapor deposited polymer used to coat electronic component circuitry for protection against environmental or physical damage
A type of paint that has the special denatured alkyd as the main ingredient. It forms the paint film with the beautiful dimensional pattern, and it is appropriate for finishing coat for plastering of various metal parts.
Industrial adhesive tapes with phosphorescent, photoluminescent or reflective properties used to mark aisleways, stairs and egress locations in low or no light situations
A type of clamp designed to hold the mitered corners of picture frames.
A collection of different types of pin fasteners packaged and sold together.
A type of chain that has links that are approximately U-shaped. The closed end of each link fits into the open end of the next one; a pin holds the two links together.
A round plate that has the shape of flange joined with the bolt to tighten the rubber ring to maintain the air-tightness of pipe joint in the cast iron pipe and polyethylene pipe.
Anisotropic barium ferrite magnet assembly that has been plastic bonded
Anisotropic ferrite magnet assembly that has been plastic bonded
Anisotropic ferrous aluminum nickel cobalt magnet assembly that has been plastic bonded
Anisotropic samarium magnet assembly that has been plastic bonded
Anisotropic strontium ferrite magnet assembly that has been plastic bonded
Plastic bonded anisotropic barium ferrite magnet that has been coated
Plastic bonded anisotropic ferrite magnet that has been coated
Plastic bonded anisotropic ferrous aluminum nickel cobalt magnet that has been coated
Plastic bonded anisotropic samarium magnet that has been coated
Plastic bonded anisotropic strontium ferrite magnet that has been coated
Plastic bonded isotropic barium ferrite magnet that has been coated
Plastic bonded isotropic ferrite magnet that has been coated
Plastic bonded isotropic ferrous aluminum nickel cobalt magnet that has been coated
Plastic bonded isotropic neodymium magnet that has been coated
Plastic bonded isotropic samarium magnet that has been coated
Plastic bonded isotropic strontium ferrite magnet that has been coated
Injection molded anisotropic barium ferrite magnet assembly that has been plastic bonded and machined
Injection molded anisotropic ferrite magnet assembly that has been plastic bonded and machined
Injection molded anisotropic ferrous aluminum nickel cobalt magnet assembly that has been plastic bonded and machined
Injection molded anisotropic samarium magnet assembly that has been plastic bonded and machined
Injection molded anisotropic strontium ferrite magnet assembly that has been plastic bonded and machined
Injection molded anisotropic barium ferrite magnet that has been plastic bonded and coated
Injection molded anisotropic ferrite magnet that has been plastic bonded and coated
Injection molded anisotropic ferrous aluminum nickel cobalt magnet that has been plastic bonded and coated
Injection molded anisotropic samarium magnet that has been plastic bonded and coated
Injection molded anisotropic strontium ferrite magnet that has been plastic bonded and coated
Injection molded isotropic barium ferrite magnet that has been plastic bonded and coated
Injection molded isotropic ferrite magnet that has been plastic bonded and coated
Injection molded isotropic ferrous aluminum nickel cobalt magnet that has been plastic bonded and coated
Injection molded isotropic neodymium magnet that has been plastic bonded and coated
Injection molded isotropic samarium magnet that has been plastic bonded and coated
Injection molded isotropic strontium ferrite magnet that has been plastic bonded and coated
Injection molded isotropic barium ferrite magnet assembly that has been plastic bonded and machined
Injection molded isotropic ferrite magnet assembly that has been plastic bonded and machined
Injection molded isotropic ferrous aluminum nickel cobalt magnet assembly that has been plastic bonded and machined
Injection molded isotropic neodymium magnet assembly that has been plastic bonded and machined
Injection molded isotropic samarium magnet assembly that has been plastic bonded and machined
Injection molded isotropic strontium ferrite magnet assembly that has been plastic bonded and machined
Injection molded anisotropic barium ferrite magnet that has been plastic bonded, machined, and coated
Injection molded anisotropic ferrite magnet that has been plastic bonded, machined, and coated
Injection molded anisotropic ferrous aluminum nickel cobalt magnet that has been plastic bonded, machined, and coated
Injection molded anisotropic samarium magnet that has been plastic bonded, machined, and coated
Injection molded anisotropic strontium ferrite magnet that has been plastic bonded, machined, and coated
Injection molded isotropic barium ferrite magnet that has been plastic bonded, machined, and coated
Injection molded isotropic ferrite magnet that has been plastic bonded, machined, and coated
Injection molded isotropic ferrous aluminum nickel cobalt magnet that has been plastic bonded, machined, and coated
Injection molded isotropic neodymium magnet that has been plastic bonded, machined, and coated
Injection molded isotropic samarium magnet that has been plastic bonded, machined, and coated
Injection molded isotropic strontium ferrite magnet that has been plastic bonded, machined, and coated
Injection molded anisotropic barium ferrite magnet that has been plastic bonded and machined
Injection molded anisotropic ferrite magnet that has been plastic bonded and machined
Injection molded anisotropic ferrous aluminum nickel cobalt magnet that has been plastic bonded and machined
Injection molded anisotropic samarium magnet that has been plastic bonded and machined
Injection molded anisotropic strontium ferrite magnet that has been plastic bonded and machined
Injection molded isotropic barium ferrite magnet that has been plastic bonded and machined
Injection molded isotropic ferrite magnet that has been plastic bonded and machined
Injection molded isotropic ferrous aluminum nickel cobalt magnet that has been plastic bonded and machined
Injection molded isotropic neodymium magnet that has been plastic bonded and machined
Injection molded isotropic samarium magnet that has been plastic bonded and machined
Injection molded isotropic strontium ferrite magnet that has been plastic bonded and machined
Injection molded anisotropic barium ferrite magnet that has been Injection molded off-tool and plastic bondedoff-tool
Injection molded anisotropic ferrite magnet that has been Injection molded off-tool and plastic bondedoff-tool
Injection molded anisotropic ferrous aluminum nickel cobalt magnet that has been Injection molded off-tool and plastic bondedoff-tool
Injection molded anisotropic samarium magnet that has been Injection molded off-tool and plastic bondedoff-tool
Injection molded anisotropic strontium ferrite magnet that has been Injection molded off-tool and plastic bondedoff-tool
Injection molded isotropic barium ferrite magnet that has been Injection molded off-tool and plastic bondedoff-tool
Injection molded isotropic ferrite magnet that has been Injection molded off-tool and plastic bondedoff-tool
Injection molded isotropic ferrous aluminum nickel cobalt magnet that has been Injection molded off-tool and plastic bondedoff-tool
Injection molded isotropic neodymium magnet that has been Injection molded off-tool and plastic bondedoff-tool
Injection molded isotropic samarium magnet that has been Injection molded off-tool and plastic bondedoff-tool
Injection molded isotropic strontium ferrite magnet that has been Injection molded off-tool and plastic bondedoff-tool
Isotropic barium ferrite magnet assembly that has been plastic bonded
Isotropic ferrite magnet assembly that has been plastic bonded
Isotropic ferrous aluminum nickel cobalt magnet assembly that has been plastic bonded
Isotropic neodymium magnet assembly that has been plastic bonded
Isotropic samarium magnet assembly that has been plastic bonded
Isotropic strontium ferrite magnet assembly that has been plastic bonded
Plastic bonded anisotropic barium ferrite magnet that has been machined and coated
Plastic bonded anisotropic ferrite magnet that has been machined and coated
Plastic bonded anisotropic ferrous aluminum nickel cobalt magnet that has been machined and coated
Plastic bonded anisotropic samarium magnet that has been machined and coated
Plastic bonded anisotropic strontium ferrite magnet that has been machined and coated
Plastic bonded isotropic barium ferrite magnet that has been machined and coated
Plastic bonded isotropic ferrite magnet that has been machined and coated
Plastic bonded isotropic ferrous aluminum nickel cobalt magnet that has been machined and coated
Plastic bonded isotropic neodymium magnet that has been machined and coated
Plastic bonded isotropic samarium magnet that has been machined and coated
Plastic bonded isotropic strontium ferrite magnet that has been machined and coated
Plastic bonded anisotropic barium ferrite magnet that has been machined
Plastic bonded anisotropic ferrite magnet that has been machined
Plastic bonded anisotropic ferrous aluminum nickel cobalt magnet that has been machined
Plastic bonded anisotropic samarium magnet that has been machined
Plastic bonded anisotropic strontium ferrite magnet that has been machined
Plastic bonded isotropic barium ferrite magnet that has been machined
Plastic bonded isotropic ferrite magnet that has been machined
Plastic bonded isotropic ferrous aluminum nickel cobalt magnet that has been machined
Plastic bonded isotropic neodymium magnet that has been machined
Plastic bonded isotropic samarium magnet that has been machined
Plastic bonded isotropic strontium ferrite magnet that has been machined
Plastic bonded anisotropic barium ferrite magnet that has been plastic bonded off-tool
Plastic bonded anisotropic ferrite magnet that has been plastic bonded off-tool
Plastic bonded anisotropic ferrous aluminum nickel cobalt magnet that has been plastic bonded off-tool
Plastic bonded anisotropic samarium magnet that has been plastic bonded off-tool
Plastic bonded anisotropic strontium ferrite magnet that has been plastic bonded off-tool
Plastic bonded isotropic barium ferrite magnet that has been plastic bonded off-tool
Plastic bonded isotropic ferrite magnet that has been plastic bonded off-tool
Plastic bonded isotropic ferrous aluminum nickel cobalt magnet that has been plastic bonded off-tool
Plastic bonded isotropic neodymium magnet that has been plastic bonded off-tool
Plastic bonded isotropic samarium magnet that has been plastic bonded off-tool
Plastic bonded isotropic strontium ferrite magnet that has been plastic bonded off-tool
Flat gasket produced by cutting various sheet plastics using punches and dies to achieve desired perimeter shapes
Seal produced by cutting plastic sheet materials using punches and dies to achieve desired perimeter shapes
Plastic part produced by an injection molding process involving injection of high pressure nitrogen gas into the resin melt stream immediately after injection of the resin allowing the gas to displace a portion of the resin and force the resin to the walls of the mold.
Plastic objects that have been machined to tolerances less than 0.020 mm for major dimensions
A type of plastic molding that includes a component placed into the mold prior to injecting the molding material.
Plastic objects that have been machined to tolerances equal to or greater than 0.020 mm for major dimensions
Gasket produced by various plastic molding processes
Seal produced from various plastic materials by using various molding processes to achieve desired dimensions and features
Dip molding produced from various plastic or plasticizer compounds
A fastener made of plastic used to secure the parts of a chain
Gasket produced by forming and cutting various plastics to achieve desired profile and perimeter shapes
Plastic objects that have been machined to tolerances equal to or greater than 0.050 mm for major dimensions
Plastic gasket produced by cutting using ultra high pressure water jets
Injection molded component consisting of various plastic materials with the addition decorative plating applied to its show surface after molding, using various plating processes
A mounted bearing used to provide support for a rotating shaft with the mounting surface on a parallel line with the axis of the shaft.
A filter that is used to change the natural light to the polarized light or detect the polarized light. This filter undertakes the role to minimize the reflection.
A type of seal made of polyacrylate produced by turning to achieve desired inner and outer diameters and thicknesses
Gasket formed by the introduction of polyacrylate materials in liquid or semi liquid form between the mating surfaces
A length of flexible material similar to rope, but thinner and shorter, made of polyester fibers braided together.
Adhesive backed fleeced or flocked PET film used as a gap filler or to prevent squeak, buzz and rattle.
Polyethylene is a thermoplastic material composed of polymers of ethylene, the polyethylene rope is very difficult to rot or mildew, it has several uses.
An adhesive-coated fastening tape wherein the carrier material is made of polyethylene. it has electrical insulation for all applications, also used to mechanically protect the joint.
Flat gasket produced by cutting polyfluoroethylene PFE sheet materials using punches and dies to achieve desired perimeter shapes
A length of flexible material similar to rope, but thinner and shorter, made of polypropylene fibers braided together.
A type of seal made of polytetrafluoroethylene PTFE produced by turning to achieve desired inner and outer diameters and thicknesses
Polyurethane polymer based liquid adhesive
A polyurethane based material used to coat electronic component circuitry for protection against environmental or physical damage
Polyurethane polymer based sealant used to fill spaces and or protect components
An adhesive-coated fastening tape whose carrier is made of polyvinyl chloride (PVC).
A type of clamp that applies maximum force in a single movement.
Precious metal object cast from centrifugal molds
Precious metal object cast from ceramic molds
Precious metal object cast from graphite molds
Precious metal object cast from investment molds
Precious metal object cast from permanent molds
Precious metal object cast from plaster molds
Precious metal object cast from sand molds
Precious metal object cast from shell molds
Precious metal object cast from v process molds
Molded seal produced from engineered materials, using close tolerance tooling to achieve significantly more precise dimensions than typically achieved
Pressed anisotropic barium ferrite magnet assembly that has been sintered
Pressed anisotropic ferrite magnet assembly that has been sintered
Pressed anisotropic ferrous aluminum nickel cobalt magnet assembly that has been sintered
Pressed anisotropic samarium magnet assembly that has been sintered
Pressed anisotropic strontium ferrite magnet assembly that has been sintered
Pressed isotropic barium ferrite magnet assembly that has been sintered
Pressed isotropic ferrite magnet assembly that has been sintered
Pressed isotropic ferrous aluminum nickel cobalt magnet assembly that has been sintered
Pressed isotropic neodymium magnet assembly that has been sintered
Pressed isotropic samarium magnet assembly that has been sintered
Pressed isotropic strontium ferrite magnet assembly that has been sintered
Pressed anisotropic barium ferrite magnet that has been sintered off-tool
Pressed anisotropic ferrite magnet that has been sintered off-tool
Pressed anisotropic ferrous aluminum nickel cobalt magnet that has been sintered off-tool
Pressed anisotropic samarium magnet that has been sintered off-tool
Pressed anisotropic strontium ferrite magnet that has been sintered off-tool
Pressed isotropic barium ferrite magnet that has been sintered off-tool
Pressed isotropic ferrite magnet that has been sintered off-tool
Pressed isotropic ferrous aluminum nickel cobalt magnet that has been sintered off-tool
Pressed isotropic neodymium magnet that has been sintered off-tool
Pressed isotropic samarium magnet that has been sintered off-tool
Pressed isotropic strontium ferrite magnet that has been sintered off-tool
Pressed anisotropic barium ferrite magnet that has been sintered and coated
Pressed anisotropic ferrite magnet that has been sintered and coated
Pressed anisotropic ferrous aluminum nickel cobalt magnet that has been sintered and coated
Pressed anisotropic samarium magnet that has been sintered and coated
Pressed anisotropic strontium ferrite magnet that has been sintered and coated
Pressed isotropic barium ferrite magnet that has been sintered and coated
Pressed isotropic ferrite magnet that has been sintered and coated
Pressed isotropic ferrous aluminum nickel cobalt magnet that has been sintered and coated
Pressed isotropic neodymium magnet that has been sintered and coated
Pressed isotropic samarium magnet that has been sintered and coated
Pressed isotropic strontium ferrite magnet that has been sintered and coated
Pressed anisotropic barium ferrite magnet that has been sintered, machined, and coated
Pressed anisotropic ferrite magnet that has been sintered, machined, and coated
Pressed anisotropic ferrous aluminum nickel cobalt magnet that has been sintered, machined, and coated
Pressed anisotropic samarium magnet that has been sintered, machined, and coated
Pressed anisotropic strontium ferrite magnet that has been sintered, machined, and coated
Pressed isotropic barium ferrite magnet that has been sintered, machined, and coated
Pressed isotropic ferrite magnet that has been sintered, machined, and coated
Pressed isotropic ferrous aluminum nickel cobalt magnet that has been sintered, machined, and coated
Pressed isotropic neodymium magnet that has been sintered, machined, and coated
Pressed isotropic samarium magnet that has been sintered, machined, and coated
Pressed isotropic strontium ferrite magnet that has been sintered, machined, and coated
Pressed anisotropic barium ferrite magnet that has been sintered and machined
Pressed anisotropic ferrite magnet that has been sintered and machined
Pressed anisotropic ferrous aluminum nickel cobalt magnet that has been sintered and machined
Pressed anisotropic samarium magnet that has been sintered and machined
Pressed anisotropic strontium ferrite magnet that has been sintered and machined
Pressed isotropic barium ferrite magnet that has been sintered and machined
Pressed isotropic ferrite magnet that has been sintered and machined
Pressed isotropic ferrous aluminum nickel cobalt magnet that has been sintered and machined
Pressed isotropic neodymium magnet that has been sintered and machined
Pressed isotropic samarium magnet that has been sintered and machined
Pressed isotropic strontium ferrite magnet that has been sintered and machined
A type of adhesive that forms a bond through the application of light pressure to the material to be bonded.
A high strength steel wire used for a compression member of pre-stressed concrete.
A steel wire with high strength used to make pre-stressed concrete that is made up of several strips.
Propulsion transmission is the mode of transmitting and controlling propulsion power of a machine. The term transmission properly refers to the whole drivetrain, including clutch, gearbox, prop shaft (for rear-wheel drive vehicles), differential, and final drive shafts.
Pure iron powder filter sintered at temperatures above 1150 degrees F or 620 degrees centigrade
Pure iron powder filter sintered at temperatures up to 1150 degrees F or 620 degrees centigrade
A mechanical seal utilizing a dynamic secondary seal or o-ring that is responsible for sealing the fluid path between the pump shaft and the inside diameter of the rotating seal face.
A first coat or layer of material given to any surface prior to application of putty.
A type of hand operated clamp designed for quickly and easily clamping all kinds of workpieces. It has a single finger release.
Tapered style shaft hub bushing
A type of clamp designed for one-handed operation with adjustable pressure.It is best for thin pieces as the jaws do not close squarely.
The fiber of the raffia is obtained from the leaves of the raffia palm that is found in South America, Africa and Madagascar, and with this raw material we get a rope very resistant and with a long life, the raffia can be also synthetic.
A type of fastener used to connect metal to wood or concrete beams such as rails to railway ties.
Bolts used to fasten railroad track to the ties.
Assembly made of a strong, narrow fabric, closely woven, ratchet buckle, and fittings at both ends principally used as strap designed to withstand strain.
Rayon is a material made from synthetic textile fibers produced by forcing a cellulose solution through fine spinnerets and solidifying the resulting filaments, with this material we get a silk-like texture rope but more resistant than silk, and it is good to control mite infestation.
A type of adhesive that works by chemical bonding with the surface material. It is usually applied in thin films.
A dry oil paint that is used in the wooden material surface, metal surface, plywood, steel frame and others. The main ingredients are coloring pigments, body pigments, dry oil, alkyd resin varnish and others, and this paint liquefied them with sufficient mixed dispersion.
Rectangular key is of rectangular cross-section and is used for power transmission.
An optical filter that reflects only the light of specific wavelength.
Refractory metals filter sintered at temperatures above 1150 degrees F or 620 degrees centigrade
Refractory metals or niobium, molybdenum, tantalum, tungsten or rhenium filter sintered at temperatures up to 1150 degrees F or 620 degrees centigrade
Bolts used to support roof in underground mining.
A type of washer used in applications requiring pre-assembly of the screw and washer, to reduce final assembly cost.
A type of bidirectional bearing having the capability of being reversible.
Right angle gearboxes are characterized by the fact that the drive shaft and the output shaft are arranged at an angle of 90 degrees. Depending on the gearbox type, the axes can intersect in a plane or cross on two parallel planes, which results in an axis offset.
Solid couplings that rigidly connect two shafts together
A bolt used to support and reinforce rock for mine shaft, tunnel, underground utility pipe conduit, cutting sloping side. It is placed by drilling a hole in the rock rocks around the mine shaft and tunnel and placing the bolt on the holes.
A double-pin-thread coupling used to connect two drill rods.
An adaptor that combines the rolling bearing sleeve and the rolling bearing rock washer. This is the auxiliary part of bearing used to easily tighten the bearings with the tapering on the inside diameter on the cylindrical shaft.
A coupling that tightens the two lines of roller chain to fit at the end of both axes attached to the sprocket to deliver the driving force.
A kind of chain comprised of inner and outer --or top-- plates that provide greater loading capacity and permit higher speed with a single power traction unit.
Large washers used in conjunction with roof bolt to support roof in underground mining.
A type of coupling designed to eliminate the use of seals in rotating and reciprocating machines such as seal-less pumps and pistons.
A bolt with a round head shape.
Gasket produced by forming and cutting rubber coated steel to achieve desired profile and perimeter shapes
A type of line thinner and shorter than a rope made of twisted fibers or threads of rubber whose insulation characteristics make it suitable for electrical applications as well as other applications.
A type seal produced by molding or extruding rubber to the desired configuration
Flat gasket produced by cutting rubber sheet materials using punches and dies to achieve desired perimeter shapes
Seal produced by cutting rubber sheet materials using punches and dies to achieve desired perimeter shapes
A type of seal made of rubber produced by turning to achieve desired inner and outer diameters and thicknesses
Gaskets produced by various rubber molding processes
Seal produced from rubber materials by using various molding processes to achieve desired dimensions and features
A type of seal consisting of rubber molded onto a rigid plastic or metal substrate used to prevent flow of a liquid or gas from one area to another and or to provide physical features
Gasket produced by forming and cutting rubber to achieve desired profile and perimeter shapes
An adhesive-coated fastening tape whose carrier is made of rubber. Coating can vary by chemical composition of adhesive material.
Rubber gasket produced by cutting using ultra high pressure water jets
This type of clamp has a flat bar with a fixed jaw that adjusts with a screw action and a sliding jaw that is locked in position along the bar to suit the job being undertaken.Used for big tasks such as sash windows, table tops, doors etc.
A specialized fastener for connecting plastic materials.
A type of ring having backup holding and sealing action. Back-up rings are washer-like devices that are used to prevent a seal from extruding through any gaps while under pressure. Back-up rings are not seals themselves, but are usually used in conjunction with O-rings in high-pressure applications and are installed in the downstream side of the gland.
A compound used to seal electrical boxes, enclosures and cable fittings
Ball bearing having two rows of balls with a common sphered raceway in the outer ring.
Plastic anchors provide drop installation security when attaching wood and tapping screws into masonry, wallboard, or concrete.
Externally-threaded fastener with a self-drilling point that drills, taps and fastens.
A coupling that tightens the conical shaped wedge with the slit between the two axes and uses the friction force with the shaft by the tightening of the taper the bolt.
A type of rivet consisting of a shaft and head having nearly half of the length hollow.This hollow portion creates a tubular structure.
A bolt with a washer capture on the shank of the bolt between the threaded portion and the bolt head.
A device for providing a connection, readily broken and restored, between two adjacent rotating shafts.
A bracket that is a metal part with one or more holes in line to support, arrange or secure the non rotational shaft or mechanical rotating shaft not completely rotated for 360 degrees.
Fastening device designed to provide a permanent one way fastening.
Fastening device designed to provide a permanent one way fastening.
A thin and often tapered or wedged, piece of material, used to fill small gaps or spaces between objects. Shims are typically used in order to support, adjust for better fit, or provide a level surface.
A product having the head with a covering metal sheath that enables the bolt to move, slide, and pivot.
A type of rivet typically installed so that the shoulder acts as a bearing surface.This allows the retained part to pivot.
A multi-leaf inverted tooth steel link chain.
A type of sprocket with geared teeth for use with silent chain.
A liquid adhesive containing silicone used in a variety of applications
A material containing silicone used to coat electronic component circuitry for protection against environmental or physical damage
A length of flexible material similar to rope, but thinner and shorter, made of silicone fibers braided together.
Flat gasket produced by cutting silicone sheet materials using punches and dies to achieve desired perimeter shapes
Seal produced by cutting silicone sheet materials using punches and dies to achieve desired perimeter shapes
Potting of electronic components using silicone based materials
Gasket formed by the introduction of silicone materials in liquid or semi liquid form between the mating surfaces
Gasket produced by various silicone molding processes
Seal produced from silicone materials by using various molding processes to achieve desired dimensions and features
A material containing silicone used to seal surfaces and joints in a variety of applications
Silicone gasket produced by cutting using ultra high pressure water jets
A 1% carbon steel tool grade supplied centerless ground to close tolerances.
Anisotropic barium ferrite magnet assembly that has been sintered
Anisotropic ferrite magnet assembly that has been sintered
Anisotropic ferrous aluminum nickel cobalt magnet assembly that has been sintered
Anisotropic samarium magnet assembly that has been sintered
Anisotropic strontium ferrite magnet assembly that has been sintered
Sintered anisotropic barium ferrite magnet that has been coated
Sintered anisotropic ferrite magnet that has been coated
Sintered anisotropic ferrous aluminum nickel cobalt magnet that has been coated
Sintered anisotropic samarium magnet that has been coated
Sintered anisotropic strontium ferrite magnet that has been coated
Sintered isotropic barium ferrite magnet that has been coated
Sintered isotropic ferrite magnet that has been coated
Sintered isotropic ferrous aluminum nickel cobalt magnet that has been coated
Sintered isotropic neodymium magnet that has been coated
Sintered isotropic samarium magnet that has been coated
Sintered isotropic strontium ferrite magnet that has been coated
Isotropic barium ferrite magnet assembly that has been sintered
Isotropic ferrite magnet assembly that has been sintered
Isotropic ferrous aluminum nickel cobalt magnet assembly that has been sintered
Isotropic neodymium magnet assembly that has been sintered
Isotropic samarium magnet assembly that has been sintered
Isotropic strontium ferrite magnet assembly that has been sintered
Sintered anisotropic barium ferrite magnet that has been machined and coated
Sintered anisotropic ferrite magnet that has been machined and coated
Sintered anisotropic ferrous aluminum nickel cobalt magnet that has been machined and coated
Sintered anisotropic samarium magnet that has been machined and coated
Sintered anisotropic strontium ferrite magnet that has been machined and coated
Sintered isotropic barium ferrite magnet that has been machined and coated
Sintered isotropic ferrite magnet that has been machined and coated
Sintered isotropic ferrous aluminum nickel cobalt magnet that has been machined and coated
Sintered isotropic neodymium magnet that has been machined and coated
Sintered isotropic samarium magnet that has been machined and coated
Sintered isotropic strontium ferrite magnet that has been machined and coated
Sintered anisotropic barium ferrite magnet that has been machined
Sintered anisotropic ferrite magnet that has been machined
Sintered anisotropic ferrous aluminum nickel cobalt magnet that has been machined
Sintered anisotropic samarium magnet that has been machined
Sintered anisotropic strontium ferrite magnet that has been machined
Sintered isotropic barium ferrite magnet that has been machined
Sintered isotropic ferrite magnet that has been machined
Sintered isotropic ferrous aluminum nickel cobalt magnet that has been machined
Sintered isotropic neodymium magnet that has been machined
Sintered isotropic samarium magnet that has been machined
Sintered isotropic strontium ferrite magnet that has been machined
Sintered anisotropic barium ferrite magnet that has been sintered off-tool
Sintered anisotropic ferrite magnet that has been sintered off-tool
Sintered anisotropic ferrous aluminum nickel cobalt magnet that has been sintered off-tool
Sintered anisotropic samarium magnet that has been sintered off-tool
Sintered anisotropic strontium ferrite magnet that has been sintered off-tool
Sintered isotropic barium ferrite magnet that has been sintered off-tool
Sintered isotropic ferrite magnet that has been sintered off-tool
Sintered isotropic ferrous aluminum nickel cobalt magnet that has been sintered off-tool
Sintered isotropic neodymium magnet that has been sintered off-tool
Sintered isotropic samarium magnet that has been sintered off-tool
Sintered isotropic strontium ferrite magnet that has been sintered off-tool
A type of fastener round in shape with a slot in its main diameter.
A type of washer having a wide range of flexibility without creating a heavy load build up.
A device that is used for the opening and shutting of the sluice. There are manual type and electric motor type in accordance with the operation method.
A bolt that has a cylindrical head with the hexagon groove on the back of the head.
Soft iron composite filter sintered at temperatures above 1150 degrees F or 620 degrees centigrade
Soft iron composite filter sintered at temperatures up to 1150 degrees F or 620 degrees centigrade
A type of rivet consisting of a shaft and head which are deformed with a hammer or rivet gun.The use of a rivet compression or crimping tool can also be used to deform these type of rivets.
Paint containing a volatile solvent carrier
Gasket formed by the introduction of solvent based materials in liquid or semi liquid form between the mating surfaces
Special fasteners refer to a type of fastening hardware that is designed for specific applications and requirements. They are typically made to order or custom-made according to the specifications of the application. Unlike standard fasteners, which have standard dimensions and are readily available, special fasteners are unique and have specific features that meet the needs of the application.Temporary fasteners are designed specifically to join two materials or objects, with the option to be removed and reused without damaging the objects they hold together. Common examples include bolts, screws, nuts, washers and studs.
A castable refractory that is used for special purposes. This is used to provide outstanding erosion resistance, abrasion resistance, spalling resistance and high strength on special parts of boiler interior, kiln, steel manufacturing, induction furnace and others.
A type of clamp comprised of a metal bar with serrations.As clamping pressure is applied the serrations lock and secure the sliding head.
A connecting device used on shafts of rotary machines to make connections. It is star or spider shaped, elastic but very resistant.
A small metal plate, thimble, or cap with fine holes through which a cellulose or chemical solution is forced in the spinning of man-made filaments.
A coupling that holds the clamp of two semi cylindrical shapes with the bolt.
A ring with overlapped or interlocked ends which may be sprung apart so that objects, as keys, may be strung upon the ring or removed from it.
A type of washer that helps keep a screw from backing out due to vibration.
Assembly consisting of multiple springs and/or springs and other components
A bolt with square shaped head.
A hook with a handle en one end for hanging, and a square shape on the other end for suspending materials. Used in meat packing for meat hanging.
Square key is of uniform cross-section and used for power transmission.
Stainless steel object cast from centrifugal molds
Stainless steel object cast from ceramic molds
Stainless steel filter produced by sintering previously compacted powders at temperatures up to 1150 degrees F or 620 degrees centigrade
Stainless steel object cast from graphite molds
Stainless steel objects that have been machined to tolerances less than 0.020 mm for major dimensions
Stainless steel filter sintered at temperatures above 1150 degrees F or 620 degrees centigrade
Stainless steel object cast from investment molds
Assembly of stainless steel objects cast from investment molds that has been machined
Stainless steel objects that have been machined to tolerances equal to or greater than 0.020 mm for major dimensions
Stainless steel object cast from permanent molds
Stainless steel object cast from plaster molds
Component stamped from cold rolled SAE series 200 stainless steel
Component stamped from cold rolled SAE series 300 stainless steel
Component stamped from cold rolled SAE series 400 stainless steel
Stainless steel object cast from sand molds
Stainless steel object cast from shell molds
Stainless steel objects that have been machined to tolerances equal to or greater than 0.050 mm for major dimensions
Stainless steel filter sintered at temperatures up to 1150 degrees F or 620 degrees centigrade
Stainless steel object cast from v process molds
A steel wire given corrosion resistance by adding 12 percent more chromium. It resists rust because of the passivity film of chromium oxide under the oxidative atmosphere.
Gasket kit produced by forming and cutting various materials to achieve desired profile and perimeter shapes
Component stamped from cold rolled steel heavily alloyed with various other metals
Component stamped from hot rolled steel heavily alloyed with various other metals
Steel alloy object cast from investment molds
Steel alloy object cast from investment molds that has been machined
Assembly ofsteel alloy objects cast from investment molds that has been machined
Steel object cast from centrifugal molds
Steel object cast from ceramic molds
Steel object cast from graphite molds
Steel objects that have been machined to tolerances less than 0.020 mm for major dimensions
Steel object cast from investment molds
Steel objects that have been machined to tolerances equal to or greater than 0.020 mm for major dimensions
Steel object cast from permanent molds
Steel object cast from plaster molds
Steel object cast from sand molds
Steel object cast from shell molds
Steel objects that have been machined to tolerances equal to or greater than 0.050 mm for major dimensions
Steel object cast from v process molds
A bolt which is supplied with the screw that is inserted with the nuts including the hexagon nuts for tightening together with the machine screw.
A type of wire made up of a coated steel wire and two lines of copper wire. The purpose is to control the electromagnetic interference from external sources.
A group of wire strands bundled or twisted together as a functional unit made of metal, it has several applications.
Structural foam part produced by an injection molding process involving injection of high pressure nitrogen gas into the resin melt stream immediately after injection of the resin allowing the gas to displace a portion of the resin and force the resin to the walls of the mold.
A type of gland seal used to prevent leakage of fluid, such as water or steam, between sliding or turning parts of machine elements.
A filter that is used generally in selecting the radiant light stripe of the area of visible rays. This filter absorbs the light of specific wavelength to limit the radiant light.
A marking device used in land surveying and topographic mapping to indicate specific elevation points. Commonly used with a theodolite.
Actuator arms in various configurations used with modular switch bases to build a complete switch assembly.
A hook connected with the iron strap of a pulley block by a swivel joint, for readily taking the turns out of a tackle.
A very strong thick rope made of synthetic material, with applications in construction and security. It is non-abrasive and very resistant.
A type of thin metal washers designed with two or more tabs which project from the outside diameter.
Mounted bearing to be used in adjustable frames.
A washer made of steel or stainless steel for use with channel sections.
Taper keys is of unifom width and height and is tapered. It is used for power transmission.
A bolt with a tapered shank and flush or protruding head that uses an interference fit to perform self-locking and perhaps self-sealing functions.
Mounted bearing having tapped holes in its base for attachment.
A bolt that has a T shaped head.
Type of tape used in packing and office supplies.
A friction reducing device designed to work with an axle, which it supports, while enabling another attached item to spin, absorbing the tension between the two.
Flat gasket produced by cutting textile sheet materials using punches and dies to achieve desired perimeter shapes
Gasket produced by forming and cutting various textile based materials to achieve desired profile and perimeter shapes
Textile gasket produced by cutting using ultra high pressure water jets
Object insert made of thermoplastic that has been blown molded
Assembly made of thermoplastic objects that has been blown molded
Object insert made of thermoplastic that has been blown molded
Assembly of objects made of thermoplastic that has been blown multiple shot insert molded
Assembly produced from multiple compression molded parts manufactured from thermoplastic resins, possibly including other components, and then finished using various materials and processes such as painting, plating and the like
Object insert made of thermoplastic that has been compression molded
Assembly made of thermoplastic objects that has been compression molded
Object insert made of thermoplastic that has been compression molded
Assembly of objects made of thermoplastic that has been compression multiple shot insert molded
Object insert made of thermoplastic that has been dip molded
Assembly made of thermoplastic objects that has been dip molded
Object insert made of thermoplastic that has been dip molded
Assembly of objects made of thermoplastic that has been dip multiple shot insert molded
Assembly produced from multiple gas assisted injection molded parts manufactured from thermoplastic resins, possibly including other components, and then finished using various materials and processes such as painting, plating and the like
Object insert made of thermoplastic that has been gas assisted injection molded
Assembly made of thermoplastic objects that has been gas assisted injection molded
Object insert made of thermoplastic that has been gas assisted injection molded
Assembly of objects made of thermoplastic that has been gas assisted injection multiple shot insert molded
Object insert made of thermoplastic that has been high precision injection molded
Assembly made of thermoplastic objects that has been high precision injection molded
Object insert made of thermoplastic that has been high precision injection molded
Assembly of objects made of thermoplastic that has been high precision injection multiple shot insert molded
Assembly produced from multiple injection molded parts manufactured from thermoplastic resins, possibly including other components, and then finished using various materials and processes such as painting, plating and the like
Object insert made of thermoplastic that has been injection molded
Assembly made of thermoplastic objects that has been injection molded
Object insert made of thermoplastic that has been injection molded
Assembly of objects made of thermoplastic that has been injection multiple shot insert molded
Object insert made of thermoplastic that has been transfer molded
Assembly made of thermoplastic objects that has been transfer molded
Object insert made of thermoplastic that has been transfer molded
Assembly of objects made of thermoplastic that has been transfer multiple shot insert molded
Object insert made of thermoset that has been blown molded
Assembly made of thermoset objects that has been blown molded
Object insert made of thermoset that has been blown molded
Assembly of objects made of thermoset that has been blown multiple shot insert molded
Object insert made of thermoset that has been compression molded
Assembly made of thermoset objects that has been compression molded
Object insert made of thermoset that has been compression molded
Assembly of objects made of thermoset that has been compression multiple shot insert molded
Object insert made of thermoset that has been dip molded
Assembly made of thermoset objects that has been dip molded
Object insert made of thermoset that has been dip molded
Assembly of objects made of thermoset that has been dip multiple shot insert molded
Object insert made of thermoset that has been gas assisted injection molded
Assembly made of thermoset objects that has been gas assisted injection molded
Object insert made of thermoset that has been gas assisted injection molded
Assembly of objects made of thermoset that has been gas assisted injection multiple shot insert molded
Object insert made of thermoset that has been high precision injection molded
Assembly made of thermoset objects that has been high precision injection molded
Object insert made of thermoset that has been high precision injection molded
Assembly of objects made of thermoset that has been high precision injection multiple shot insert molded
Object insert made of thermoset that has been injection molded
Assembly made of thermoset objects that has been injection molded
Object insert made of thermoset that has been injection molded
Assembly of objects made of thermoset that has been injection multiple shot insert molded
Object insert made of thermoset that has been transfer molded
Assembly made of thermoset objects that has been transfer molded
Object insert made of thermoset that has been transfer molded
Assembly of objects made of thermoset that has been transfer multiple shot insert molded
Thermostat housing is used in internal combustion engines to house the thermostat that controls the coolant flow.
Thread locking compounds or also known as “Threadlockers” are an adhesive that can be applied to the threads of a fastener to prevent it from loosening over time due to vibration or shifting parts.
A ball bearing which is used in cases where the load is applied to the shaft direction. This is mainly used for mid- to low speed.
A roller bearing which is used in the cases where the load is applied to the axis direction.
Tin object cast from centrifugal molds
Tin object cast from ceramic molds
Tin object cast from graphite molds
Tin object cast from investment molds
A type of wire made with the main material of tin or tin alloy.
Tin object cast from permanent molds
Tin object cast from plaster molds
Component stamped from tin plated copper
Tin object cast from sand molds
Tin object cast from shell molds
Tin object cast from v process molds
Titanium alloy filter sintered at temperatures above 1150 degrees F or 620 degrees centigrade
Titanium alloy filter sintered at temperatures up to 1150 degrees F or 620 degrees centigrade
Titanium object cast from centrifugal molds
Titanium object cast from ceramic molds
Titanium object cast from graphite molds
Titanium object cast from investment molds
A type of wire made with the main material of titanium or titanium alloy.
Titanium object cast from permanent molds
Titanium object cast from plaster molds
Titanium object cast from sand molds
Titanium object cast from shell molds
Titanium object cast from v process molds
A type of fastener in the shape of a T with a central threaded hole that is designed to fit around and secure a bolt or a screw leaving a flush surface.
A type of safety washer provided with a hook-shaped projection extending into a hole in the surface which bears the nut.
A type of lock washer that has teeth around either the inner or outer perimeter of the washer to reduce vibration.
A screw that has a trapezoidal shape for the cross section of screw thread.
A type of rivet consisting of a shaft and head being completely hollow lengthwise forming a tubular structure.
A parallel gear drive is one in which the high and low speed shaft are on the same horizontal plane and parallel to each other. Parallel shaft gear boxes are usually selected for high torque and high horsepower applications.
An additive that prevents fading or changing of color due to exposure to ultra violet light.
A type of coupling where the angular or offset misalignment of the shaft reaches values which cannot be accommodated by flexible couplings.
Dip molding produced from various urethane compounds
A rope made of nylon spun yarn, a synthetic fiber, with outstanding weatherability and is easy to handle for flexible and non-slippery features.
Seal mounted on shafts allowing their thin, tapered V flanges to seal against a surface at right angles to the shaft
Forging made of aluminum that is forged at a warm temperature and has been heat treated
Forging made of aluminum that is forged at a warm temperature and has been heat treated and cold sized
Forging made of beryllium that is forged at a warm temperature and has been heat treated and cold sized
Forging made of brass that is forged at a warm temperature and has been heat treated and cold sized
Forging made of bronze that is forged at a warm temperature and has been heat treated and cold sized
Forging made of copper that is forged at a warm temperature and has been heat treated and cold sized
Forging made of ferrous alloy that is forged at a warm temperature and has been heat treated and cold sized
Forging made of iron that is forged at a warm temperature and has been heat treated and cold sized
Forging made of lead that is forged at a warm temperature and has been heat treated and cold sized
Forging made of magnesium that is forged at a warm temperature and has been heat treated and cold sized
Forging made of non ferrous alloy that is forged at a warm temperature and has been heat treated and cold sized
Forging made of precious metal that is forged at a warm temperature and has been heat treated and cold sized
Forging made of stainless steel that is forged at a warm temperature and has been heat treated and cold sized
Forging made of steel that is forged at a warm temperature and has been heat treated and cold sized
Forging made of tin that is forged at a warm temperature and has been heat treated and cold sized
Forging made of titanium that is forged at a warm temperature and has been heat treated and cold sized
Forging made of zinc that is forged at a warm temperature and has been heat treated and cold sized
Forging made of beryllium that is forged at a warm temperature and has been heat treated
Forging made of brass that is forged at a warm temperature and has been heat treated
Forging made of bronze that is forged at a warm temperature and has been heat treated
Forging made of copper that is forged at a warm temperature and has been heat treated
Forging made of ferrous alloy that is forged at a warm temperature and has been heat treated
Forging made of iron that is forged at a warm temperature and has been heat treated
Forging made of lead that is forged at a warm temperature and has been heat treated
Forging made of magnesium that is forged at a warm temperature and has been heat treated
Forging made of non ferrous alloy that is forged at a warm temperature and has been heat treated
Forging made of precious metal that is forged at a warm temperature and has been heat treated
Forging made of stainless steel that is forged at a warm temperature and has been heat treated
Forging made of steel that is forged at a warm temperature and has been heat treated
Forging made of tin that is forged at a warm temperature and has been heat treated
Forging made of titanium that is forged at a warm temperature and has been heat treated
Forging made of zinc that is forged at a warm temperature and has been heat treated
Forging made of aluminum that is forged at a warm temperature and has been machined
Forging made of aluminum that is forged at a warm temperature and has been machined and heat treated
Forging made of beryllium that is forged at a warm temperature and has been machined and heat treated
Forging made of brass that is forged at a warm temperature and has been machined and heat treated
Forging made of bronze that is forged at a warm temperature and has been machined and heat treated
Forging made of copper that is forged at a warm temperature and has been machined and heat treated
Forging made of ferrous alloy that is forged at a warm temperature and has been machined and heat treated
Forging made of iron that is forged at a warm temperature and has been machined and heat treated
Forging made of lead that is forged at a warm temperature and has been machined and heat treated
Forging made of magnesium that is forged at a warm temperature and has been machined and heat treated
Forging made of non ferrous alloy that is forged at a warm temperature and has been machined and heat treated
Forging made of precious metal that is forged at a warm temperature and has been machined and heat treated
Forging made of stainless steel that is forged at a warm temperature and has been machined and heat treated
Forging made of steel that is forged at a warm temperature and has been machined and heat treated
Forging made of tin that is forged at a warm temperature and has been machined and heat treated
Forging made of titanium that is forged at a warm temperature and has been machined and heat treated
Forging made of zinc that is forged at a warm temperature and has been machined and heat treated
Forging made of beryllium that is forged at a warm temperature and has been machined
Forging made of brass that is forged at a warm temperature and has been machined
Forging made of bronze that is forged at a warm temperature and has been machined
Forging made of copper that is forged at a warm temperature and has been machined
Forging made of ferrous alloy that is forged at a warm temperature and has been machined
Forging made of iron that is forged at a warm temperature and has been machined
Forging made of lead that is forged at a warm temperature and has been machined
Forging made of magnesium that is forged at a warm temperature and has been machined
Forging made of non ferrous alloy that is forged at a warm temperature and has been machined
Forging made of precious metal that is forged at a warm temperature and has been machined
Forging made of stainless steel that is forged at a warm temperature and has been machined
Forging made of steel that is forged at a warm temperature and has been machined
Forging made of tin that is forged at a warm temperature and has been machined
Forging made of titanium that is forged at a warm temperature and has been machined
Forging made of zinc that is forged at a warm temperature and has been machined
A machine bolt that has is assembled with the washer that cannot be separated for one or more thereof.
A screw that is rolled after assembling the washer onto the machine screws to secure the washer not to be loosened from the small screws.
Gasket kit produced by cutting using ultra high pressure water jets
Type of spring designed to maintain tension between parts.
A type of washer designed to offer a compensating spring force and maintain a load or take up shock.
Large bushing having swivel action which is part of rotary table in oilfield operations.
A type of clamp with a nylon band that wraps around the object and is tightened with a ratchet.Can be used with corner gripping pieces so that pressure is evenly distributed.
A type seal welded or bonded directly to the upper housing, permitting removal of the upper housing without a loss of fill fluid
A bolt that has an external screw. The screw part has small protrusions above and below the head for welding.
Weld nuts have a projection for spot welding. It is classified by function.
A nut welded or mechanically attached to a metal part for the purpose of joining multiple parts.
Studs designed to be welded or mechanically secured to a metal part.
Steels screws easy to recognize because of the flat wing head, with that head we can screw with hands, this screw is in accordance with the DIN 316 standard.
Type of spring used in various formed wire configurations.
An anchor is a device, normally made of metal , have to safely absorb all impacts from handling, lifting and assembly and transmit them into the component.
Wire rope is constructed using multiple wires and strands. This means that the weight, pressure and stress of a load is spread out across multiple pieces of metal, rather than being reliant on one wire or strand alone.
A type of metal device with a funnel shaped receptacle or basket made to secure the tip of the wire rope hardened by the casted metal or wedge.
Zinc object cast from centrifugal molds
Zinc object cast from ceramic molds
Zinc object cast from graphite molds
High pressure die casting made of zinc
Zinc high pressure die casting that has been machined
Zinc high pressure die casting assembly that has been machined
Zinc object cast from investment molds
Zinc object cast from permanent molds
Zinc object cast from plaster molds
Zinc object cast from sand molds
Zinc object cast from shell molds
Zinc object cast from v process molds